cisco console port configuration
Console Port Telnet SSH Handling and Reset Button
The console port on the router is an EIA/TIA-232 asynchronous serial connection with no flow control and an RJ-45 connector The console port is used to access the router and is located on the front panel of the Route Processor For information on accessing the router using the console port see Using Cisco IOS XE Software |
Does Cisco provide a console cable?
Cisco does not provide these cables. These cables are widely available from other sources. Console cable is usually provided with the Console Cable Kit. Note: The console port does not support modem control or hardware flow control.
How do I configure a modem on the console port?
When a modem is connected to the console port, a remote user can dial in to the router and configure it. To configure a modem on the console port, perform these steps: Connect the RJ-45 end of the adapter cable to the console port on the router. Use the show line command to determine the async interface of the console port:
What is the console port on a Cisco router?
The console port on the router is an EIA/TIA-232 asynchronous, serial connection with no flow control and an RJ-45 connector. The console port is used to access the router and is located on the front panel of the Route Processor. For information on accessing the router using the console port, see Using Cisco IOS XE Software.
Where is the console port located in Cisco IOS XE software?
The console port is used to access the router and is located on the front panel of the Route Processor. For information on accessing the router using the console port, see Using Cisco IOS XE Software. If you are using the console port to access the router, you are automatically directed to the Cisco IOS command-line interface (CLI).
Configuring Terminal Settings and Sessions
Cisco Nexus 3000 Series NX-OS Fundamentals Configuration Guide Release 6.x You can configure the following parameters for the console port: Data bits. |
Initial Switch Configuration
You can connect the console port to a PC serial port for local administrative access to the Cisco MDS. 9000 Family switch. Note. The PC must support VT100 |
Configuring the Switch with the CLI-Based Setup Program
Step 1 If you are connecting the switch USB console port to a Windows-based PC for the first time install the USB driver. See Installing the Cisco Microsoft |
Configuring the Switch with the CLI-Based Setup Program
Connect the USB cable from the Windows PC to the Cisco switch. 5. From the Device Manager page expand Ports (COM & LPT). Select USB Serial Port. Right-click |
Cisco 350 Series Managed Switches Quick Start Guide Firmware
If you are managing the switch through a console port connection the link is retained. To configure the switch using the web-based interface: STEP 1 Power on |
Cisco 1100 Series Software Configuration Guide Cisco IOS XE Fuji
6 Mar 2017 Viewing Console Port SSH |
Getting Started
Initial Configuration Using Console Port on page 1 Configure the Firepower 4100/9300 chassis hardware (see the Cisco Firepower Security Appliance ... |
Console Port, Telnet, SSH Handling, and Reset Button - Cisco
Configuring Console Port for Modem Connection , on page 9 Restrictions and Notes for Console Port, Telnet, and SSH • Configuring the diagnostic and wait |
Console Port, Telnet, SSH Handling, and Reset - Cisco
Cisco IR1101 Integrated Services Router Software Configuration Guide-Console Port, Telnet, SSH Handling, and Reset |
Configuring Terminal Settings and Sessions - Cisco
Configure your terminal emulator with 9600 baud, 8 data bits, 1 stop bit, and no parity COM1 Port A COM1 port is an RS-232 port with a DB-9 interface that |
Configuring Terminal Settings and Sessions - Cisco
Cisco Nexus 7000 Series NX-OS Fundamentals Configuration Guide, Release 4 2 You can configure the following parameters for the console port: Specifies |
Initial Switch Configuration - Cisco
Subnet mask for the switch's management interface IP address of the default gateway This section describes how to connect the RS-232 console port to a PC |
Initial Switch Configuration - Cisco
You can connect the console port to a PC serial port for local administrative access to the Cisco MDS 9000 Family switch Note The PC must support VT100 |
Appendix - Starting a Router Terminal or Console Session - Cisco
The console port is an asynchronous serial port that allows you to connect to the device for initial configuration through a standard RS-232 port with an RJ-45 |
Cisco IOS Terminal Services Command Reference
when the configured number of minutes occurs on the virtual terminal (vty) line The absolute-timeout command terminates the connection after the specified |
Configuring the Switch with the CLI Setup Program - Cisco
▫ A straight-through or crossover Category 5 Ethernet cable to connect your computer to the switch port Do not use the RS232 serial console port for express |
Configuring the Switch with the CLI-Based Setup Program
You can use the console port to perform the initial configuration If you are connecting the switch to a Cisco redundant power system (RPS), refer to the |