cisco sonet interface configuration
|
Configuring Clear Channel SONET Controllers
Cisco IOS XR Interface and Hardware Component Configuration Guide for the Cisco CRS Router Release 5 3 x -Configuring Clear Channel SONET Controllers |
How to do Cisco configuration?
How to configure a Cisco Router?
1Step 1: Create a Lab in Packet Tracer.
2) Step 2: Access Command Line Interface.
3) Step 3: Enter the Privileged EXEC Mode.
4) Step 4: Switch to Global Configuration Mode.
5) Step 5: Change the router name.
6) Step 6: Assign IP Addresses.
7) Step 7: Assign IP Address to R2.
8) Step 8: Assign IP Address to PC.How do I enable interface on Cisco router?
To enable an interface, it must be activated using the no shutdown command. (This is similar to powering on the interface.) The interface must also be connected to another device (a hub, a switch, or another router) for the physical layer to be active.
The Router Configuration mode allows users to configure routing protocols such as OSPF, BGP, EIGRP and so on.
This mode is accessed by entering the "configure terminal" command in Privileged EXEC mode and then entering the "router" command followed by the name of the routing protocol you want to configure.
What is POS interface in Cisco?
This module describes the configuration of Packet-over-SONET/SDH (POS) interfaces.
POS interfaces provide secure and reliable data transmission over SONET and Synchronous Digital Hierarchy (SDH) frames using Cisco High-Level Data Link Control (HDLC) protocol or Point-to-Point Protocol (PPP) encapsulation.
|
Configuring the Channelized OC-12/T3 SONET/SDH Optical
Configure the channelized interfaces for Frame Relay as described in the Cisco IOS Wide-Area Router(config)# controller sonet slot/port. |
|
Configuring Clear Channel SONET Controllers on Cisco IOS XR
Cisco IOS XR Interface and Hardware Component Configuration Guide for the Cisco The commands used to configure the physical SONET port are grouped under ... |
|
SONET Controller Commands on the Cisco IOS XR Software
Cisco IOS XR Interface and Hardware Component Command Reference for the Cisco XR All SONET-related configurations of a SONET-based physical port are ... |
|
Packet-over-SONET Interface Commands
This module describes the Cisco IOS XR commands used to configure monitor |
|
Packet-over-SONET Interface Commands on the Cisco ASR 9000
This module describes the Cisco IOS XR commands used to configure monitor |
|
Configuring Clear Channel SONET Controllers on Cisco IOS XR
Cisco IOS XR Interface and Hardware Component Configuration Guide for the Cisco XR 12000 Series Router. OL-28390-02. Configuring Clear Channel SONET |
|
Packet-over-SONET Interface Commands on the Cisco IOS XR
For Packet-over-SONET/SDH (POS) interfaces the default encapsulation is HDLC. Command Modes. Interface configuration. Command History. Modification. Release. |
|
Configuration des paramètres dhorloge dans les interfaces de
Ce document passe en revue les paramètres de la source de l'horloge recommandés pour les interfaces de routeurs de port paquet sur SONET (POS) dont la |
|
Dépannage des alarmes de la couche physique sur les liaisons
Alarmes sur les couches SONET. Indicateurs d'alarme. Dépannage. Dépannage avec les commandes de bouclage. Configurer une interface pour le bouclage interne. |
|
SONET Controller Commands - Cisco CRS Router
You must configure a SONET controller before you can configure a Packet-over-SONET/SDH. (POS) interface or a Spatial Reuse Protocol (SRP) interface. All SONET- |
|
Configuring SONET - Cisco
SONET T3 Configuration Parameters The following parameters affect SONET T3 configuration: • Clock — Specifies the clock source for T3 link Description — Specifies the description of the controller Framing — Specifies the type of a framing on T3 interface Loopback — Sets the T3 link in the loopback mode |
|
Configuring Clear Channel SONET Controllers - Cisco
The commands for configuring the Layer 1 SONET controllers are provided in the Cisco IOS XR Interface and Hardware Component Command Reference |
|
Packet-over-SONET Interface Commands - Cisco
This module provides command line interface (CLI) commands for configuring Packet-over-SONET/SDH (POS) on the Cisco NCS 6000 Series Router |
|
Configuring Clear Channel SONET Controllers - Cisco
The commands for configuring the Layer 1 SONET controllers are provided in the Cisco IOS XR Interface and Hardware Component Command Reference |
|
SONET Controller Commands on the Cisco IOS XR Software
Cisco IOS XR Interface and Hardware Component Command Reference for the Cisco XR 12000 Series Router, Release 5 1 x-SONET Controller Commands on |
|
Configuring the OC-3c/STM-1, OC-12c/STM-4, and OC-48c - Cisco
IETF RFC 2615, PPP over SONET/SDH with 1+x43 self-synchronous payload Configure the POS interfaces for Frame Relay as described in the Cisco IOS |
|
Configuring the Channelized OC-12/T3 SONET/SDH Optical - Cisco
The configuration below is basic, and you may need to specify additional interface parameters depending on your network requirements To configure the POS |
|
Présentation rapide de la technologie SONET - Cisco
Questions de configuration Débogage Le SONET définit des signaux Optiques et une structure de trame synchrone pour le trafic numérique Les couches Optiques d'interface ont des relations hiérarchiques ; les constructions de chaque |
|
Présentation des différences élémentaires entre tramage - Cisco
configuration d'interface afin de configurer pour le transport synchrone 1 niveau du module (STM- 1) : Router(config-if)#atm sonet stm-4 Référez-vous aux |
|
SONET/SDH - Cisco
The type of SONET/SDH high-order interface IpCore Configuration Sts1OrAu4OrAu3Number The STS1 number inside a channelized controller configured in |
