Switch(config)#ip routing Note: Si le commutateur n'accepte pas la commande ip routing, effectuez une mise à niveau soit vers l'image SMI Cisco IOS Version
howto L intervlanrouting
The Catalyst 4500 series switch supports Layer 3 interfaces with the Cisco IOS IP and IP routing protocols Layer 3, the network layer, is primarily responsible for
l int
Each subinterface must support the encapsulation protocol used by the trunk port on SwitchA Configuration on SwitchA would be as follows: SwitchA(config)#
multilayer switching
Multilayer Switching Architecture on Catalyst Switches • MLS Memory Table Architecture • CEF-Based MLS Configuration, Verification, and Troubleshooting
samplechapter
Layer 3 interface Switch(config-if)# no switchport ▫ Step 3 Configure the IP address and IP subnet mask This
en SWITCH v Ch
User's Manual of PLANET 24-Port Gigabit Layer 3 Stackable Managed Switch with 4 10G Slots Models: SGS-6341-24T4X, SGS-6341-24P4X and SGS-6341-
EM SGS Series Configuration Guide v .
Overview of the Multilayer Switch Module Internal Interfaces, on page 14 — Overview of InterVLAN Routing, on page 15 — Configuring VTP and VLANs on the
newaries
between Cisco and any other company (0406R) Catalyst 3550 Multilayer Switch Software Configuration Guide Copyright © 2004 Cisco Systems, Inc All rights
ccmigration a cb
The multilayer switch must have IP routing enabled ▫ A switch virtual interface ( SVI) exists for VLAN 1 by default On a multilayer switch, a logical (layer
CCNA D S T STEP
A maximum of 125 buffers per port in a port group. • Fair bandwidth arbiters. • Device Manager Quick Config Wizard for the Cisco MDS 9148 Switch. • Redundant
Switch(config-if)# no switchport. Switch(config-if)# ip address 10.101.101.1 255.255.255.0. Multilayer switches support configuring a VLAN as a logical
Catalyst 3560 Switch Software Configuration Guide Cisco IOS Release CLI—The Cisco IOS software supports desktop- and multilayer-switching features.
The physical Layer 3 interfaces allow the. Catalyst 4500 series switch to be configured like a traditional router. Page 2. 23-2. Software Configuration Guide—
Catalyst 3550 Multilayer Switch Software Configuration Guide. Copyright © 2004 Cisco Systems Inc. All rights reserved.
1 rack unit (RU) fixed-configuration multilayer switch. • Entry-level enterprise-class intelligent services. • LAN Base Image installed. WS-C2960-48TT-L.
User's Manual of PLANET 24-Port Gigabit Layer 3 Stackable Managed Switch with 4 10G Slots 4.3.1 Switch IP Addresses Configuration Task List .
Cisco MDS 9000 Family Switch-to-Switch Interoperability Configuration Guide. • Cisco MDS NX-OS Release Compatibility Matrix for IBM SAN Volume Controller
Catalyst 3550 Multilayer Switch Command Reference. OL-8566-01 mvr (global configuration) 2-256 mvr (interface configuration) 2-259 pagp learn-method 2-262.
is a Catalyst 3550 Gigabit Ethernet switch and the standby command switch is a Catalyst 3550 Fast Multilayer Switch Software Configuration Guide).
The commands and configurations described in this guide apply only to the devices that provide routing services Commands and configurations for Catalyst 5000
The physical Layer 3 interfaces allow the Catalyst 4500 series switch to be configured like a traditional router Page 2 23-2 Software Configuration Guide—
Catalyst 3550 Multilayer Switch Software Configuration Guide Copyright © 2004 Cisco Systems Inc All rights reserved
Multilayer Switching - Routing Between VLANs By default a switch will forward both broadcasts and multicasts out every port but the originating port
The purpose of this chapter is to provide you with details architecture and methods of multilayer switching on Catalyst switches
This chapter describes how to configure Multilayer Switching (MLS) on the Catalyst 5000 and 2926G series switches Note For complete syntax and usage
In layer -3 switch there is no need to configure management vlan for its interface vlan is the management vlan 4 3 QinQ Configuration 4 3 1 QINQ Overview
For more information on setting passwords and privilege levels refer to the Catalyst 3550 Multilayer Switch Software Configuration Guide Step 3 Click Web
Configuring Inter-VLAN Routing on a Multilayer Switch Describing Basic Switch Commands to Support Attachment of a Cisco IP Phone
:
Cisco MDS 9148 Multilayer Fabric Switch Quick Start Guide